- 您现在的位置：买卖IC网 > Sheet目录397 > BH1621FVC-TR (Rohm Semiconductor)IC AMBIENT LIGHT SENSOR 5WSOF
BH1621FVC
Technical Note
● Cautions on use
1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as supply voltage ( Vmax ), temperature range of operating conditions
( Topr ), etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open
circuit. If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take
physical safety measures including the use of fuses, etc.
2) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
3) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between
the terminal and the power supply or the GND terminal, the ICs can break down.
4) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
5) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig.
After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition,
for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the
transportation and the storage of the set PCB.
6) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals; such as to apply to the input terminals a
voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to
the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
7) Thermal design
Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (pd) in
actual states of use.
8) Treatment of package
Dusts or scratch on the photo detector may affect the optical characteristics. Please handle it with care.
9) Rush current
When power is first supplied to this IC, rush current may flow instantaneously. Because it is possible that the charge
current to the parasitic capacitance of internal photo diode or the internal logic may be unstable. Therefore, give special
consideration to power coupling capacitance, power wiring, width of GND wiring, and routing of connections.
10) The exposed central pad on the back side of the package
There is an exposed central pad on the back side of the package. Please mount by footprint dimensions described in the
Jisso Information for WSOF5. This pad is GND pin, therefore there is a possibility that LSI malfunctions and heavy-current
is generated.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
8/9
2012.02 - Rev.D
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
BH1715FVC-TR
IC AMBIENT LIGHT SENSOR 6-WSOF
BH1750FVI-TR
IC AMBIENT LIGHT SENSOR WSOF6
BH1751FVI-TR
IC AMBIENT LIGHT SENSOR 6WSOF
BISDK02BI-03
KIT BISM II BLUETOOTH/802.11B/G
BMS4007
MOSFET N-CH 75V 60A TO-220ML
BS107AG
MOSFET N-CH 200V 250MA TO-92
BS107PSTZ
MOSFET N-CHAN 200V TO92-3
BS108G
MOSFET N-CH 200V 250MA TO-92
相关代理商/技术参数
BH162240DGG
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver with 30ohm series termination resistors
BH162240DL
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver with 30ohm series termination resistors
BH162244DGG
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit buffer/line driver with 30ohm series termination resistors 3-State
BH162244DL
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit buffer/line driver with 30ohm series termination resistors 3-State
BH162245ADGG
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-Bit bus transceiver with 30ohm series termination resistors 3-State
BH162245ADL
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-Bit bus transceiver with 30W series termination resistors (3-State)
BH16240ADGG
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver 3-State
BH16240ADL
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:16-bit inverting buffer/driver 3-State